Aller au contenu
manulemalin

Parametrage Fibaro fgt-001 et fgs214

Recommended Posts

Bonjour a tous

 

J'ai depuis quelques temps installé des têtes thermostatique FGT-001, Je viens d'installer aujourd'hui un module fgs-214 sur ma chaudière en remplacement de mon thermostat Nest

J'ai eu beau lire les manuels et chercher sur ce forums (et sur d'autres) la façons de paramétrer ma HC3, ou les modules pour que si une des têtes a besoin de chauffer une pièces, elle puisse activer la chaudière (c'est quand même le but LOL )

 

Quelqu’un aurait-il un lien ou une explication sur ce sujet

 

En vous en remerciant par avance

 

Emmanuel

Partager ce message


Lien à poster
Partager sur d’autres sites

En continuant mes recherche, a priori, il faut ajouter un appareil "autre appareils" sur la HC3 et choisir la quick app : Fibaro Heat Activator

Hélas , ça n active toujours pas la chaudière :unsure:

Partager ce message


Lien à poster
Partager sur d’autres sites

Je ne sais pas t'aider, car je n'ai pas de chaudière, mais j'ai compris des nombreux échanges à ce sujet sur le forum que c'est un sujet complexe.

 

Je te laisse commencer par étudier quelques un des sujets pour te rendre compte à quel point il est complexe de piloter son chauffage central à la fois par domotisation des radiateurs ET de la chaudière.

En général, c'est l'un ou l'autre, et ça c'est facile.

 

https://www.google.fr/search?q=site%3Adomotique-fibaro.fr+gestion+chauffage+chaudière

 

 

Partager ce message


Lien à poster
Partager sur d’autres sites

Merci de ton intérêt Lazer 

J avais déjà fait pas mal de recherche sur le sujet, mais le lien que tu as posté m a fait remonter un post que je n avais pas vu.

ca confirme que je suis dans la bonne direction, je présage quand même un bug car le paramètrage de l’app heat activator me paraît cohérent (mais n enclenché rien) 

j ai envoyé une demande à Fibaro en même temps, si j ai une réponse intéressante, j en ferai le retour ici 

 

 

Partager ce message


Lien à poster
Partager sur d’autres sites

Bonjour a tous

 

J'ai donc, au final, réussi a avoir l'information qui me manquait pour que mes têtes thermostatiques Fibaro puissent être autonome et qu'elle puissent activé la chaudière individuellement

voici donc la réponse du SAV que je "colle" ici puisque c'est parfaitement clair et explicite

En espérant que cela serve a quelqu’un :)

 

attachment?token=eyJ0eXAiOiJKV1QiLCJhbGciOiJIUzI1NiJ9.eyJpZCI6NjIwMDkzNDIyMjMsImRvbWFpbiI6InN1cHBvcnQtZmliYXJvLmZyZXNoZGVzay5jb20iLCJhY2NvdW50X2lkIjoxMzY5MDc2fQ.s9tthDaprgxufkSwlMjXPg_9uxl6JQx6hJ-favhZt10

  1. Check the device version 4.7 or newer. (If the device has a lower version, update the device, then perform the soft reconfiguration.)

  2. In the Configuration section tick the heating medium demand reports option in parameter 2.

 

Our parameters are below:

The Heat Controller:

attachment?token=eyJ0eXAiOiJKV1QiLCJhbGciOiJIUzI1NiJ9.eyJpZCI6NjIwMDkzNDIyMjUsImRvbWFpbiI6InN1cHBvcnQtZmliYXJvLmZyZXNoZGVzay5jb20iLCJhY2NvdW50X2lkIjoxMzY5MDc2fQ.L6X4888WWDxAF3_EyiKB2DGFsHo3ZFkDwSl74Ba-XSI

attachment?token=eyJ0eXAiOiJKV1QiLCJhbGciOiJIUzI1NiJ9.eyJpZCI6NjIwMDkzNDIyMjYsImRvbWFpbiI6InN1cHBvcnQtZmliYXJvLmZyZXNoZGVzay5jb20iLCJhY2NvdW50X2lkIjoxMzY5MDc2fQ.DVvWir-vVoCzPp-mYJdxaxJSgb7j8YM7rEy0w1Xu870

 

The Heat Activator:

attachment?token=eyJ0eXAiOiJKV1QiLCJhbGciOiJIUzI1NiJ9.eyJpZCI6NjIwMDkzNDIyMjIsImRvbWFpbiI6InN1cHBvcnQtZmliYXJvLmZyZXNoZGVzay5jb20iLCJhY2NvdW50X2lkIjoxMzY5MDc2fQ.qJQMrOimnZZz5bVYrnYE20c3N7t6HUl-K-fKTEufzzE

 

attachment?token=eyJ0eXAiOiJKV1QiLCJhbGciOiJIUzI1NiJ9.eyJpZCI6NjIwMDkzNDIyMjQsImRvbWFpbiI6InN1cHBvcnQtZmliYXJvLmZyZXNoZGVzay5jb20iLCJhY2NvdW50X2lkIjoxMzY5MDc2fQ.-m0G_0Q1_GrZOkgj94p7etZXCqzeOiOvVCqzGMun5io

 

 

The Heat controller should be correctly calibrated ad mounted on the valve. If we had an unmounted device it does not work. Check the calibration if the valve is open/closed properly."

 

 

Summarazing that heat activator issue :

 

"It looks as if the Heat Activator plugin was turned off by default after adding it to the system, but the information on the preview says that it is different "Plugin is turned on".

 

After pressing the "Turn on" button and forcing the plug-in to turn on, everything starts to work properly. Twisting and unscrewing make the connected switch turn on and off.

 

Solution?

 

Currently, to be able to add a plugin that will work properly:

 

  1. Add Heat Activator

  2. Set device and plugin parameters

  3. Force plug-in activation by "Turn on" button in plugin preview


attachment?token=eyJ0eXAiOiJKV1QiLCJhbGciOiJIUzI1NiJ9.eyJpZCI6NjIwMDkzNDIyMjEsImRvbWFpbiI6InN1cHBvcnQtZmliYXJvLmZyZXNoZGVzay5jb20iLCJhY2NvdW50X2lkIjoxMzY5MDc2fQ.L9cF4PJ41Jzgx7Zuhk3dJWSk7MIO7gquUYMGvB8NDgc"

  • Like 1

Partager ce message


Lien à poster
Partager sur d’autres sites

×